Soil
Automatic Soil Compactor
Standards
AASHTO T180; AASHTO T193; AASHTO T99
ASTM D1557;ASTM D698; BS 1377:4; BS 1990
EN 13286-2; EN 13286-47
Product code
AR- 030 Automatic Soil Compactor
AR- 030/1 ASTM Rammer
AR- 030/2 EN Rammer
Soil Compaction Moulds and Rammers
Standards
ASTM D558; D698, D1557; AASHTO T99; T180; BS 1377-4
Product code
AR- 011 Standard Proctor Mould ASTM
AR- 012 Modified Proctor Mould ASTM
AR- 013 Standard Proctor Rammer ASTM
AR- 014 Modified Proctor Rammer ASTM
Moulds are used for determining the relationship between the moisture content and density of compacted soil. Made of plated steel, includes collar, mould body and base plate.Rammers are used to compact the soil sample in the Proctor Moulds. Made of plated steel. Guide sleeve with vent holes.
Liquid Limit Device
Standards
ASTM D4318; BS 1377:2; AASHTO T89
Product code
AR- 004 MANUAL TYPE
AR- 005 MOTORIZED TYPE
Cone Penetromete
Standards
BS 1337:2; NF P94-052-1
Product code
AR- 002 Manuel Cone Penetrometer
AR- 003 Automatic Cone Penetrometer
AR- 003/1 Penetration Needles
AR- 003/2 AluminumMoisture Content
For determining the liquid limit of soils. This is specially useful to obtain reliable and accurate results of those soil which have low plasticity index. The percentage moisture contents determined when cone with half angle of 15-30 minutes under a total sliding weight of 148 gm penetrates 25mm gives the liquid limit.
Plastic Limit Test Set
Standards
ASTM D4318; AASHTO T90; BS 1377:2
UNI 10014; UNE 103-104; NF P94-051
Product code
AR- 007 Plastic Limit Test Set
AR- 007/1 Glass Plate 300 x 300 x 10 mm
AR- 007/2 Rod Caliper / diameter 3 mm
AR- 007/3 Mixing Porcelain Dish
AR- 007/4 Flexible Spatula
AR- 007/5 Aluminium Moisture Tins
Used to determine the lowest moisture content of a soil, by which a sample can be rolled into threads dia. 3 mm without breaking the same neither longitudinally or transversely.
Shrinkage Limit Set
Standards
ASTM D427; ASTM T92; UNI 10014;
UNE 103-108;NF P94-060; BS 1377:2
Product code
AR- 006 Shrinkage Limit Set
When the water content of a fine-grained soil is reduced below the plastic limit, shrinkage of the soil mass continues until the shrinkage limit is reached. This method of test covers the determination of the shrinkage limit, shrinkage ratio, volumetric shrinkage and linear shrinkage
AR- 006/1 Shrinkage dish.
AR- 006/2 Glass measuring cylinder.
AR- 006/3 Prong plate.
AR- 006/4 Two moisture content tins.
AR- 006/5 Spatula.
POCKET PENETROMETERS
Standards
ASTM D2573-94
Product cod
POCKET PENETROMETERS
POCKET PENETROMETERS (Dial)
Pocket penetrometer is used to classify the cohesive soils based on the approximate consistencies measured in the field and to determine the uniaxial compressive strength.
Measuring Range: 0 to 4.5 kgf / sq.cm.
Dimensions: 19×153 mm.
Pocket Type Vane Shear Apparatus
Standards
ASTM D427; ASTM T92; UNI 10014;
UNE 103-108;NF P94-060; BS 1377:2
Product code
Used to quickly find shear strength of binding materials of soil in laboratory or field conditions.
Direct reading dial as Kgf/cm2.
Measuring range: 0-1 Kgf/cm2
Complete with stainless steel vane.
Weight: 300 gr.
Proving Ring Penetrometer
Standards
TS 1900-1;ASTM D2937;BS 1377/9
Used to determine the bearing capacity of subgrades, or to measure soil compaction. Light and easy to handle in the field. A rapid means of determining the penetration resistance of soil in shallow exploration surveys. Includes: 30°, 1 sq. in. (6.45 sq cm) cone; 250 lb. (1.1kN) capacity proving ring; brake type dial indicator, holds final reading until manually released; 3/4” (19mm) dia. shaft, graduated at 6”, (152mm) intervals; 3/4” (19mm) dia. extension rod, graduated at 6” (152mm) intervals; cast aluminum T-handle. Weight:6,8 kg
Sand Cone Density Set
Standards
AASHTO T191; ASTM D1556
Product code
AR- 019 Sand Cone Density Set
AR- 019/1 Sand Cone Set 6.
AR- 019/2 Sand Cone Base Plate 6.
AR- 019/3 Plastic Sand Jar 5 lt.
For the on site determination of the degree of compaction.Complete set includes double cone, plastic sand jar 5lt capacity and metal tray.
